Bedienungsanleitung TRENDNET TDM-E400 QUICK INSTALLATION GUIDE

[. . . ] Verbinden Sie das RJ-45-Kabel (und/oder schließen Sie das USBKabel am TDM-C400 an). Verbinden Sie das Netzteil mit dem ADSL2+ Ethernet-Router. 4. Warten Sie 60 Sekunden, damit das Gerät hochfahren kann. Überprüfen Sie, dass die LEDs WAN und LAN leuchten. 3 Deutsch 3. [. . . ] Daraufhin erscheint die Anzeige, dass Ihre Änderungen erfolgreich übertragen wurden. 10. Der Reboot Mode (Neustartmodus) steht standardmäßig auf Reboot (Neu starten). 11. Klicken Sie auf die Schaltfläche Reboot (Neu starten). 12. Schalten Sie die Stromversorgung während des Neustarts des ADSL2+ ModemRouters bitte nicht aus. Ihre Installation ist beendet! Weitere Informationen zu den Konfigurations- und erweiterten Einstellungen des TDM-E400/TDM-C400 finden Sie im Abschnitt , , Problembehandlung" der Bedienungsanleitung auf der beiliegenden CD-ROM oder auf der Website von TRENDnet unter http://www. trendnet. com. 10 Deutsch Troubleshooting Q1: POWER LED does not illuminate after the product is turned on. A1: Verify that you are using the power cable provided with the device and that it is securely connected to the ADSL2+ modem and a wall socket/power strip. Q2: I am not sure what type of Internet broadband connection I have for my DSL connection. A2: You can contact your Internet Service Provider's (ISP) Customer Service or Technical Support Department for the correct information. Q3: I specified the IP address 192. 168. 1. 254 in my Web browser, but an error messages says, "The page cannot be displayed. How can I get into the TDM-E400 / TDM-C400 web configuration page?A3: Please check your hardware and TCP/IP settings again by following the instructions in the QIG. Make sure the Power, WAN and the LAN LEDs are on. Then try to access the configuration page using your Web Browser again. Q4: INTERNET LED does not illuminate after phone cable is attached. A4: Verify that a standard telephone cable (called an RJ-11 cable) like the one provided is securely connected to the ADSL port and your wall phone jack. Allow about 30 seconds for the device to negotiate a connection with your ISP. Verify that you are using a straight-through type Ethernet cable to the uplink port on a hub or a cross-over type cable to a stand-alone PC. If you connected the device to an ordinary hub port (not Uplink), you must use a straight-through cable. (To check: hold the connectors at each end of the cable side-by-side with the plastic spring facing down. Looking at the wires from left to right, if the first, second, third, and sixth wires are the same color on the two connectors, then it is a straight-through type. On a cross-over type, wire 1 on one connector should be the same color as wire 3 on the other. The same is true of wires 2 and 6. ) Q5: Ethernet LED does not illuminate after Ethernet cable is attached. A5: Verify that the Ethernet cable is securely connected to your LAN hub or PC and to the ADSL2+ mdoem. [. . . ] Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Check with you Local Authority or Retailer for recycling advice. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. ADVERTENCIA En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón necesario para su funcionamiento. [. . . ]