Bedienungsanleitung TRENDNET TFC-110S20D5 QUICK INSTALLATION GUIDE

[. . . ] Für den TFC-110MM/MST/MSC ist ein Multimodus- und für den TFC-110S15/S30/S60/S100/ S20D3/S20D5/S40D3/S40D5 ein Einzelmodus-Kabel erforderlich. Verbinden Sie den Ethernet-Port des Glasfaserkonverters über ein RJ-45-Ethernetkabel mit einem Ethernet-Port Ihres Umschalters (z. B. Verbinden Sie das Netzteil mit der Buchse auf der Rückseite des Konverters. Hinweis: Auf der anderen Seite der Glasfaserverbindung müssen TX- und RXKabel vertauscht werden. [. . . ] Cable(/125 µm ) Distance /Connector MMF (50µm or 62. 5µm ) SC MMF (50µm or 62. 5µm ) ST MMF (50µm or 62. 5µm ) MT-RJ SMF (9µm or 10µm ) SC SMF (9µm or 10µm ) SC SMF (9µm or 10µm ) SC SMF (9µm or 10µm ) SC Bi-directional SMF (9µm or 10µm ) SC Bi-directional SMF (9µm or 10µm ) SC Bi-directional SMF (9µm or 10µm ) SC Bi-directional SMF (9µm or 10µm ) SC SMF (9µm or 10µm ) SC 2 km TFC-110MSC 1300nm TFC-110MST 10/100 100m 100 1300nm 2 km TFC-110MM 10/100 100m 100 1300nm 2 km TFC-110S15 10/100 100m 100 1300nm 15 km TFC-110S30 10/100 100m 100 1300nm 30 km TFC-110S60 10/100 100m 100 1300nm 60 km TFC-110S100 10/100 100m 100 1300nm 100 km TFC-110S20D3 10/100 100m 100 TX: 1310nm RX: 1550nm TX: 1550nm RX: 1310nm TX: 1310nm RX: 1550nm TX: 1550nm RX: 1310nm 20 km TFC-110S20D5 10/100 100m 100 20 km TFC-110S40D3 10/100 100m 100 40 km TFC-110S40D5 10/100 100m 100 40 km TFC-15MS100 100 2 km 100 1300nm 15 km Note: MMF (multi-mode fiber); SMR (single-mode fiber) 5 Troubleshooting Q1: After connecting the Fiber converter, the LEDs do not turn on. A1: First, check that the power outlet is receiving power. Second, make sure the power adapter is firmly connected to the Fiber converter and the power outlet. Third, make sure the Ethernet and the Fiber cables are connected. Q2: All the LEDs are on, but I can't make a connection. A2: First, verify that you are using the proper fiber cable (e. g. multi-mode fiber cable for multi-mode converter; single-mode fiber cables for single-mode converters). Second, verify that the TX and RX cables have been reverse on the opposite Fiber connection. Third, power down the fiber converters and the switches. Wait 15 seconds, then plug the switches and the fiber converters back in. Q3: What is the maximum distance that is supported by the fiber converter?A3: Please reference section 4 for distance information. If you still encounter problems or have any questions regarding the Fiber Converters please contact TRENDnet's Technical Support Department. 6 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. Fiber Converters 5 Year Limited Warranty If a product does not operate as warranted above during the applicable warranty period, TRENDnet shall, at its option and expense, repair the defective product or deliver to customer an equivalent product to replace the defective item. All products that are replaced will become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. [. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Check with you Local Authority or Retailer for recycling advice. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. [. . . ]