Bedienungsanleitung ZYXEL NWA-3500 QUICK GUIDE

[. . . ] Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks ZyNOS (ZyXEL Network Operating System) is a registered trademark of ZyXEL Communications, Inc. [. . . ] If you are configuring the ZyAIR from a computer connected to the wireless LAN and you change the ZyAIR's ESSID or WEP settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the ZyAIR's new settings. Channel Select a channel from the drop-down list box depending on your particular region. 10-6 Wireless LAN ZyAIR B-4000 Hot Spot Gateway Table 10-1 Wireless LABEL WEP Encryption DESCRIPTION Select Disable to allow all wireless computers to communicate with the access points without any data encryption. Select Mandatory to enable WEP data encryption. Then click WEP Key Setup to open a screen where you can configure the WEP keys on the ZyAIR. Beacon Interval RTS Threshold Fragmentation Threshold DTIM Interval Set the number of milliseconds that should pass between sending out a beacon. Enter a value between 0 and 2442 to enable an RTS/CTS handshake to avoid retransmitting due to hidden nodes. Enter a value between 256 and 2446 to enable a fragmentation threshold. This sets the maximum size of data fragments that can be sent. Use a low setting if there is a great deal of radio interference. This setting, always a multiple of the beacon period, determines how often the beacon contains a delivery traffic indication message (DTIM). Default Apply Click this button to load the factory default wireless LAN settings. Click Apply to save the settings. 10. 3. 1 Configuring WEP Keys When you select Mandatory in the WEP Encryption field in the Wireless screen, click WEP Key Setting to display the screen as shown. 10-8 Wireless LAN ZyAIR B-4000 Hot Spot Gateway Figure 10-6 WEP Key Setup The following table describes the labels in this screen. Table 10-2 WEP Key Setup LABEL WEP Encryption Mode DESCRIPTION Select 64 bit, 128 bit or 256 bit for the WEP key length. Select the type of input mode from the drop-down list box. Select ASCII to enter the WEP keys as ASCII characters. Select HEX to enter the WEP keys as hexadecimal characters. Wireless LAN 10-9 ZyAIR B-4000 Spot Gateway Table 10-2 WEP Key Setup LABEL 1. . . 4 DESCRIPTION Enter the WEP keys in the fields provided and select a key as the default key to use. If you select 64 bit in the WEP Encryption field. Enter either 10 hexadecimal digits in the range of "A-F", "a-f" and "0-9" (e. g. 11AA22BB33) for HEX key type or Enter 5 printable ASCII characters (case sensitive) ranging from "a-z", "A-Z" and "0-9" (e. g. MyKey) for ASCII key type. If you select 128 bit in the WEP Encryption field, Enter either 26 hexadecimal digits in the range of "A-F", "a-f" and "0-9" (for example, 00112233445566778899AABBCC) for HEX key type or Enter 13 printable ASCII characters (case sensitive) ranging from "az", "A-Z" and "0-9" (for example, MyKey12345678) for ASCII key type. If you select 256 bit in the WEP Encryption field, Enter either 58 hexadecimal digits in the range of "A-F", "a-f" and "0-9" for HEX key type or Enter 29 printable ASCII characters (case sensitive) ranging from "az", "A-Z" and "0-9" for ASCII key type. ASCII WEP keys are case sensitive. [. . . ] See Extended Service Set Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Ethernet Cable Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-1 Ethernet Cable Length Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . I-1 Ethernet Cable Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-1 Extended Service Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3, 10-2 Extended Service Set IDentification. . . . . . . . . . . . . 10-6 F Factory Ethernet Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]