Bedienungsanleitung DURKOPP 888

[. . . ] 888 Spezialnähmaschine Betriebsanleitung Instruction manual D GB Postfach 17 03 51, D-33703 Bielefeld · Potsdamer Straße 190, D-33719 Bielefeld Telefon +49 (0) 521 / 9 25-00 · Telefax +49 (0) 521 / 9 25 24 35 · www. duerkopp-adler. com Ausgabe / Edition: 09/2010 Änderungsindex Rev. index: 04. 0 Printed in Federal Republic of Germany Teile-Nr. /Part. -No. : 0791 888740 Alle Rechte vorbehalten. Eigentum der Dürkopp Adler AG und urheberrechtlich geschützt. Jede, auch auszugsweise Wiederverwendung dieser Inhalte ist ohne vorheriges schriftliches Einverständnis der Dürkopp Adler AG verboten. [. . . ] In the machines with the motor on the table top mount the guard (2) on the machine head (the guard is included in of the motor part set) and mount the guard (3) on the motor (the guard is included in the motor package). In the machines with the motor on the sewing head and with 1, 55:1 toothed belt driving gear, mount the proximity switch (6). It is included in the "kit for motor". In all machines with the motor on the machine head mount the guards (4) and (5) (they are included in of the motor part set). Doing this, observe the correct angle position: if the needle is in the upper dead point, there should be the 0° value on the hand wheel scale. 12 4. 4 Adjustment of pedal position 90 ° 2 3 2 1 ­ ­ Adjust the side position of the pedal (1) so that its center lies on the needle axis. Adjust the draw rod (2) so that the foot axis is perpendicular to the pedal surface. GB Caution!Failure to keep the determined pedal position can cause damage to the operator's locomotion system. 13 4. 5 Fitting the knee lever and oil pump pipe 1 4 6 5 3 8 7 9 10 10°± 5° ­ ­ ­ ­ ­ ­ ­ Lift the sewing foot with the hand lever. Screw the screw (5) with the washer (6) in the shaft (3). Attach the pipe (7) with the clips (8) and install the suction basket (9). Tilt the machine head and adjust the knee lever (10) according to the picture. Adjust the knee pad. 14 4. 6 Fitting the proximity switch 2 1 4 3 5 6 ­ ­ ­ ­ ­ The proximity switch (1) is mounted to certain positioning motors (drives) only. In that case it is part of the drive supply. Slide the proximity switch (1) in the arrow (2) direction on the hand wheel shaft so that the carrier pin (3) fits in the proximity switch groove. Attach the proximity switch with two screws (4). Remove the back cover and pull the proximity switch cable (5) through according to the picture. Attach the cable with a clip (6). GB 15 4. 7 Fitting the connecting cable, control panel and sewing diode lamp on the machine head 1 4 2 3 6 5 9 7 8 ­ ­ ­ ­ ­ ­ ­ The connecting cable (1) is supplied with every machine with the positioning motor (drive). The control panel (2) had to be ordered separately (optional equipment). When ordering a control panel, a bracket (3) is always supplied together with it. The sewing lamp LED (5) is an optional equipment. Two types of brackets are supplied together with it to enable the installation of the lighting body in two positions. Position (7) should be used if a guide for sewing material is mounted on the machine. Dismantle the upper cover and back cover of the machine head. [. . . ] The angle is set by the corresponding parameter value (it is not, however, identical with the parameter value). The position parameter values have already been set ­ see chapter 6. 1. 3. The reference position still remains to be set. The reference position is defined by the angle 105° on the hand wheel scale. [. . . ]