Bedienungsanleitung EPSON EPL-5600

[. . . ] Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U. S. ) failure to strictly comply with SEIKO EPSON CORPORATION's operating and maintenance instructions. SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by SEIKO EPSON CORPORATION. EPSON and EPSON ESC/P are registered trademarks and EPSON ESC/P 2 is a trademark of SEIKO EPSON CORPORATION. Speedo, Fontware, FaceLift, Swiss, and Dutch are trademarks of Bitstream Inc. [. . . ] For details, see "Using the OneTouch Modes" on page 1-7. SelecType Settings 5-13 Toner Save When you select On, the printer saves toner by substituting a gray shade for the black inside of characters. The characters are outlined in full black on the right and lower edges. Note: You can also make Toner Save settings directly from OneTouch Mode 2. Density You can adjust the print density to make your printout lighter (1) or darker (5). Note: Increasing the print density increases toner consumption. If you select darker print, you may need to replace the imaging cartridge more often. Top Offset Make fine adjustments to the vertical position of the printing on the page. c Left Offset Caution: Be sure that the printed image does not extend beyond the edge of paper. Otherwise, you may damage the printer. Makes fine adjustments to the horizontal position of the printing on the page. This is useful for fine adjustment when you are using the manual feed mode. c 5-14 Caution: Be sure that the printed image does not extend beyond the edge of paper. Otherwise, you may damage the printer. SelecType Settings T Offset B Adjusts the vertical printing position on the back side of the paper when printing on both sides. Use this if the printout on the back side is not where you expected. This item is available only when the Duplex Unit is installed. L Offset B Adjusts the horizontal printing position on the back side of the paper when printing on both sides. Use this if the printout on the back side is not where you expected. Make sure the On Line light is not blinking when you reboot the printer. Page Count Displays the total number of sheets printed by this printer. SelecType Init. Erases all the SelecType settings you have changed, and resets them to the factory default settings. Parallel Menu These settings control communication between the printer and the computer when using a parallel interface. Item Speed Bi-D Buffer Size Values (default is in bold) Fast, Normal Nibble, ECP, Off Normal, Maximum, Minimum Speed Specifies the pulse width of the ACKNLG signal when receiving data in the Compatibility mode or Nibble mode. When this option is set to Fast, the pulse width is about 1 ms. When this option is set to Normal, the pulse width is about 10 ms. Bi-D Allows you to specify the bidirectional communication mode. When you select Off, bidirectional communication is disabled. SelecType Settings 5-19 Buffer Size Determines the amount of memory to be used for receiving data and printing data. If set to Maximum, more memory is allocated for receiving data. If set to Minimum, more memory is allocated for printing data. Serial Menu These settings control communication between the printer and the computer when using a serial interface. Item Word Length Baud Rate Values (default is in bold) 8, 7 9600, 19200, 38400, 57600, 76800, 115200, 300, 600, 1200, 2400, 4800 None, Even, Odd 1, 2 On, Off On, Off, Robust Normal, Maximum, Minimum Parity Stop Bit DTR Xon/Xoff Buffer Size Word Length You can select an 8-bit or 7-bit word length. See your computer manual and software documentation for the proper setting. Baud Rate Use this option to set the data transfer rate (baud) for the serial interface. The baud rate is measured in bits per second (bps). See your computer manual and software documentation for the proper setting. 5-20 SelecType Settings Parity When this option is set to None, parity checking is disabled. The parity bit, if used, provides a basic form of error detection. See your computer manual and software documentation for the proper setting. Stop Bit Use this option to set the number of stop bits for each character of information sent to the printer. [. . . ] When OCR-B is used: 36 pt or more (Up to 96 pt in Windows NT) Recommended sizes are 36 pt, 72 pt, 108 pt and 144 pt. The following codes are inserted automatically and need not be input by hand. t Left/right quiet zone t Start/Stop character (when not input) t Check digit Print Sample EPSON Codabar EPSON Codabar CD EPSON Codabar Num EPSON Codabar CD Num Working with Fonts D-23 Glossary ASCII American Standard Code for Information Interchange. A standardized way of assigning codes to characters and control codes. The system is widely used by manufacturers of computers, printers, and software. auto line feed A printer feature in which each carriage return code (CR) is automatically accompanied by a line feed (LF) code. bitmap font The dot-by-dot representation of a font. [. . . ]