Bedienungsanleitung ZYXEL M-102 QUICK GUIDE

[. . . ] Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks Trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. ii Copyright VES-1000 Series Ethernet Switch ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. [. . . ] Connect the top ports of MDF 1 to the telephone company. Installation Scenarios 3-9 VES-1000 Series Ethernet Switch Chapter 4 Hardware Connections This chapter shows you how and where to make hardware connections. Before you make your hardware connections, make sure that your VES-1000 Series switch is safely and securely positioned. 4. 1 Rear Panel Connections 4. 1. 1 Power Cord Make sure you are using the correct power source. The following figure shows the rear panel of the M-102 only. The VES-1008 differs in that the 12-volt DC power socket is located on the front panel. There are no sockets or switches on the back panel of the VES-1008. Figure 4-1 The M-102 Rear Panel The VES-1008 has a 12-volt DC power socket located on the front panel. This allows for the convenient placing of the unit in locations where space may be a limitation. To connect the power to the unit, plug the round end of the plug on the supplied power adaptor into the power socket on the front panel. Connect the other end of the supplied power adaptor to a power outlet. Always use the ZyXEL supplied power adaptor as the VES-1008 may be damaged if third party power adaptors are used. To connect the M-102 only, connect the female end of the power cord to the power receptacle on the rear panel of your M-102 (just to the right of the warning sticker) as seen in Figure 4-2. Connect the other end of the cord to a power outlet. You also need to change the default VLAN configuration ­ refer to the VES-1000 Series User's Guide. Figure 4-7 Daisy-chaining Connections Hardware Connections 4-5 VES-1000 Series Ethernet Switch Chapter 5 Turning On Your VES-1000 Series Switch This chapter discusses the fans and LEDs of the VES-1000 Series switch after you turn it on. 5. 1 Introduction Before turning on your VES-1000 Series switch, make sure you: · · Have attached a computer to the VES-1000 Series switch serial port as explained previously. Can see the status LEDs on the front panel while you view the VT100 terminal emulator. Push the power switch (located on the front panel of VES-1008 and on the back panel for the M-102) to the ON position. The VES-1000 Series switch will automatically run a self-test that takes approximately 20 seconds. The SYS LED will remain on if your VES-1000 Series switch has started normally. If the SYS LED does not turn on then recheck your connections or refer to the Hardware Troubleshooting chapter. Make sure you can feel and/or hear the fans working (M-102 only) -- working fans emit a low buzz and blow air. The fans are located on side panel that is to the left of the front panel. Refer to the Hardware Troubleshooting chapter to test the fans if they are not working. 5. 2 Front Panel LEDs The following figures show the front panels for both the VES-1008 and the M-102. LEDs show the operational status of your VES-1000 Series switch. Please also refer to the Troubleshooting chapter to see how the front panel LEDs may aid in troubleshooting. Figure 5-1 VES-1008 Front Panel Figure 5-2 M-102 Front Panel Turning On Your VES-1000 Series Switch 5-1 VES-1000 Series Ethernet Switch Table 5-1 VES-1000 Series Switches: LED Descriptions LED PWR SYS COLOR Green Green STATUS ON OFF Blinking ON OFF ALM VDSL Red Green ON OFF Blinking ON OFF 10 Mbps Green Blinking ON OFF 100 Mbps Yellow Blinking ON OFF The system is turned on. The system is rebooting and performing self-diagnostic tests. [. . . ] 5-2, 6-1 R T Rack Mounting Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1, 2-5 Rack-mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Rack-mounted M-102 Installation. . . . . . . . . . . . . . . . . . . . 2-4 Rear Panel Connections Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 2 Telco-50 . . . . . . . . . . . . . . 3-3, 3-4, 3-6, 3-8, 3-9, 6-2, D, E, H Telnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G, H Testing In-house Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3, 6-4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]